No description
Find a file
robotics 1114bbde52 v3.1
Built from v3.0: platform at the owner's 200 mm target (was 250).

- Drive: the chain, sprockets, Tsubaki TL200 limiter and NMRVS30 worm
  gear motor (the 60 mm gearbox stack set 250 mm) are replaced by four
  friction-wheel units, one per diagonal bay: StepperOnline
  17HS19-1684S-PG19 (NEMA 17, 19.2:1; listing ratings SOURCED) lying
  radially with a D40 x 20 PU wheel on the rotating plate top at r 200,
  a pivoted carrier, a spring preload and a hood over each nip. The
  wheel slip is the torque limit (1.25 x running, 41 N m at the ring,
  29 N at the arm end), set at commissioning. Gear motor at slip x 2.0:
  2.07 of 3 N m. Wheel, spring and grip are ASSUMED open items.
- Deck: 2 x 15 mm plywood (was 2 x 18); free edge 8.5 of 10 MPa.
  The deck is set by the spider ring plate over the rotating plate
  (199 mm); radials over the arm 188, drive units 184, skirt slot 156.
  No running gap, finger gap or guard reduced.
- Counterweight: 63.5 kg, all 25 mm inside the deck edge (cw_in 25,
  was 45): fixed tier 31.8 kg bridging the arm, stepped down under the
  drive units, over a 31.8 kg sliding trim; trim holes chosen for the
  middle of the lens range. Residual <= 0.44 kg m at every setting.
- Rotating plate D430 (was 350): the wheels' track. Outer-ring bolts
  countersunk (the ring plate is 2 mm over the plate). Hub sleeve 48 mm
  above the bearing inner ring (was 60 hanging from the hub).
- Step box: 100 / 100 mm risers, 5.8 kg, interlock kept.
- Fixed in the model: v3.0's arm clamp cheeks stopped 6 mm short of the
  rotating plate (nothing joined the arm to the turntable); they now
  reach it. The fascia band now stops at the arm slot top (at 200 mm it
  would have entered the 25 mm finger gap: 21.7 mm, caught by the slot
  check).
- New checks, each shown failing on the old state or a variant: arm
  clamp cheeks reach the plate (v3.0: 6.0 mm); spider ring plate under
  the radial roots (variant 3 mm low); hub sleeve engagement and 2 mm
  above the bearing (v3.0 rule at 200 mm: sleeve into the bearing);
  wheel on the plate with the tread 5 mm inside (D420 plate: 0 mm);
  gear motor at slip x rating_factor (2 wheels: 4.14 N m), x
  margin_misuse vs momentary (1 wheel r 40: 10.4 N m), slip before
  stall (direct drive: 1.04 > 0.52 N m); drive units vs arm and plate.
  Removed with the chain drive: chain, limiter and NMRV030 gearbox rows.
- Criterion changes: the hub-sleeve feasibility rule "+25 mm key room
  above the bearing inner ring" (no key is needed there: the screws go
  in from below) is replaced by the measured engagement and the 2 mm
  gap; the clamp cheeks under the rotating plate are judged by the 2 mm
  internal rule against the spider ring plate, not the 15 mm deck-frame
  rule (the plate lies between them).
- Views, GLB (Drive under Static, Turntable under Rotating) and FreeCAD
  colours regenerated.

VERIFY: PASS f01f3054808c (995/995 checks pass)

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-23 09:22:07 +08:00
.claude/skills/freecad-headless v2.0-simple 2026-10-21 16:17:28 +08:00
03_CAD v3.1 2026-10-23 09:22:07 +08:00
04_CALCS v3.1 2026-10-23 09:22:07 +08:00
.gitattributes v1.6 baseline, verified locally 2026-10-21 13:43:35 +08:00
.gitignore v2.1 2026-10-21 17:14:27 +08:00
CLAUDE.md v3.1 2026-10-23 09:22:07 +08:00
README.md v3.1 2026-10-23 09:22:07 +08:00
run.sh v2.3 2026-10-22 09:20:17 +08:00

Project 360 v3.1 — 200 mm, 1.15 m booth for 3–4 adults, rim friction drive, step box with interlock, 1.3–1.9 m pole with reach-coupled tilt

One stationary Ø1.15 m plywood platform, 200 mm high, on a fixed centre column. The camera arm turns underneath it on its own slewing bearing around the column. Four small drive units press polyurethane wheels on the rotating plate. Guest load runs plywood → radials → column → base box → floor and never passes through the bearing, which carries only the arm and counterweight. Not fabrication-ready: it needs a structural and safety review, the drive tests and the sandbag proof test below.

Run

FREECADCMD="C:/Users/Admin/AppData/Local/Programs/FreeCAD 1.1/bin/freecadcmd.exe" ./run.sh

04_CALCS/calcs.py size works from 03_CAD/P360_params.csv:

  • sizes the booth and places as many guests as fit;
  • lays the deck at the lowest height the parts below it allow (or the owner's target, if higher);
  • picks the arm reaches and the safe (reach, tilt) pin pairs.

03_CAD/build_booth.py (FreeCAD) builds:

  • 03_CAD/P360_booth_v3_1.FCStd (with colours, visibility and an isometric camera for the FreeCAD GUI);
  • the Godot export 03_CAD/P360_booth_v3_1.glb;
  • 03_CAD/views/*.png (clean pictures, no text).

It then measures the model, rebuilding the arm, pole and counterweight at every pin setting: each (reach, tilt) pair at each of the 7 lens heights. calcs.py check runs every check against the CAD and the export and must end with VERIFY: PASS (995 checks). Run logs and JSON go to logs/.

While iterating, P360_FAST=1 builds only the lowest and highest lens per pin pair and skips the views. The verified run is always the full one.

Current design

Item Value
Platform One full-circle level, Ø1.15 m, top 200 mm (the owner's target), seamless laminated 2 × 15 mm plywood (worst case, the free edge at the rim: 8.5 of 10 MPa). The edge is a 25 × 12.7 mm aluminium rim with a 6 mm fascia and a flush 50 mm yellow nosing; the fascia stops at the top of the arm slot so it never enters the finger gap. The closed skirt has the arm slot (z 26–116 mm, 25 mm finger gaps)
Height 200 mm, with every running gap, finger gap and guard kept. What each layer needs, lowest first:
  • skirt slot 156 mm;
  • drive units 184 mm (gear motor top 148, wheel hood top 151, 3 mm gap);
  • radials over the arm 188 mm (15 mm running gap);
  • spider ring plate 199 mm (2 mm over the rotating plate, then the 40 mm radials, 12 mm hub plate and 30 mm plywood).
So 200 mm is reached with 1 mm to spare on the tightest layer
Capacity Two target groups, both checked for overlap and lip clearance, loads and framing:
  • 4 standard adults (500 × 300 mm footprint each) in rows of 1 + 2 + 1 along the entrance axis, all facing the entrance, 28 mm inside the lip;
  • 3 guests with one larger guest (600 × 400 mm, 150 kg) across the back and two adults side by side at the front, turned sideways, 9 mm inside the lip.
4 guests including a larger one do not fit on 1.15 m (they would need about Ø1.2 m). Guests stand touching, in a close pose. The footprints are ASSUMED; confirm with 3- and 4-person standing tests. The front row boards last
Entrance Removable step box at the entrance, 90° from the parked arm. It is 600 × 300 mm with its top at 100 mm, giving risers of 100 / 100 mm and a 310 mm going. It has a non-slip mat with a flush yellow nosing, a carry handle and rubber feet; it weighs 5.8 kg and clears the parked arm and counterweight by ≥ 58 mm. A positive-opening NC interlock switch behind the kick band, below the arm slot, is pressed by a striker on the box. It is in series with the run enable: Start is blocked while the box is in place, and a broken wire also blocks
Frame (symmetric) 8 identical one-piece RHS 80 × 40 × 4 flat radials on one welded spider (48 mm hub sleeve on the column spigot, Ø320 hub plate on top, 8 mm ring plate welded under the radial roots), with a flat deck bearer outside the hub plate. 8 identical outriggers RHS 50 × 30 × 4 flat sit directly under them on a Ø600 base box, with pads at r 510 inside the skirt. No ballast is needed
Bearing igus PRT-01-100-M-ARG, inner ring on the column flange. The Ø430 × 10 rotating plate bolts to the outer ring (countersunk M5, flush) and carries both arm clamps, whose cheeks are welded to its underside
Drive (new) Four drive units, one in each diagonal bay (45°, 135°, 225°, 315°). Each is a StepperOnline 17HS19-1684S-PG19 (NEMA 17 stepper, 19.2:1 planetary; listing: 3 N·m max permissible, 5 N·m momentary, 80 %; 0.52 N·m holding) lying radially, with a Ø40 × 20 mm polyurethane wheel on its shaft running on the rotating plate top at r 200 mm (5 mm inside the plate edge). The gear motor rides on a carrier pivoted on a cross bracket welded between the radials; a torsion spring at the pivot presses the wheel down. A steel hood guards each nip.
  • Ring torque at full speed: 33.1 N·m (Izz 39.9 kg·m²: acceleration 9.9 + bearing friction 21.6 N·m at the assumed μ 0.2).
  • Each wheel: 41 N running, slips at 52 N (1.25 × running). The wheel slip is the torque limit (it replaces the v3.0 Tsubaki limiter): 41 N·m at the ring, 29 N at the arm end.
  • Gear motor at slip × rating factor 2.0: 2.07 of 3 N·m; motor 0.11 of 0.26 N·m (50 % of holding) at 907 rpm.
  • Spring preload needed to set that slip: 65–129 N per wheel over the assumed grip μ 0.4–0.8. The slip is set and recorded at commissioning, whatever the grip turns out to be.
Arm (telescoping) Outer RHS 100 × 40 × 3 tube to r 825; inner RHS 80 × 30 × 3 × 915 mm. Reach 1045 / 1195 / 1265 / 1350 mm.
  • 1195 is the minimum for the vertical pole: it frames both target groups head to feet and keeps the phone ≥ 400 mm plus 50 mm sway from their heads.
  • 1045 is for the leaning pole only.
  • The others extend the tilt range.
The stroke is limited by the 300 mm overlap, the clamp and the clevis
Pole (telescoping) Top at 1.3–1.9 m (lens 1.24–1.84 m, 7 pin positions 100 mm apart). Outer Al SHS 50 × 50 × 3 (top 1.145 m), inner Al SHS 40 × 40 × 3. Misuse pushes above 1.145 m land on the inner tube. Pins run across the arm. Sway 11.4 Hz. The top setting frames both target groups head to feet at every pin pair; lower settings frame them only at some reaches (reported)
Pole tilt Pinned range −5° (inward) to +15° (outward) from vertical, against the owner's ±45° target. Safe range at every lens height:
  • 1045: +9.5 to +15.2°, holes +10 and +15;
  • 1195: 0.0 to +10.2°, holes 0, +5 and +10;
  • 1265: −2.5 to +7.9°, holes 0 and +5;
  • 1350: −5.5 to +5.1°, holes −5, 0 and +5.
Outward lean is capped by the venue against the pole-face rule (continuous limit 15.4°). Inward lean is capped by the phone's head clearance and the framing.
Mechanism: a D10 lock pin with R-clip and lanyard. Hole radii are 70 / 100 / 130 / 160 mm, all ≥ 2.2 d0 apart, and the hinge axis is raised to 44 mm for the inward hole. The tilt gate on the outer arm tube opens only at the 10 safe pairs (measured). The 6 mm clevis cheeks and 5 mm leaf walls are checked for pin bearing and bending
Full 45° lean (information) With this platform it needs a 5.74 × 5.74 m venue. In the 4.6 m venue no platform size works
Counterweight (entirely under the deck) 63.5 kg of steel in two parts, every part 25 mm inside the deck edge (inside the brush skirt):
  • a fixed tier, 31.8 kg, ±63.9°: full height (z 84–103) at r 361–533, outboard of the drive units and 15 mm under the radials, stepped down to z 96 at r 235–361 so it passes 10 mm under the drive units. It sits on the counterweight arm and bridges it;
  • a sliding trim, 31.8 kg, ±75°, 30 mm high, under the tier. It slides on one grid of holes 28.6 mm (2.2 d0) apart to balance each pin setting, each hole chosen for the middle of the lens range.
Balance residual ≤ 0.44 kg·m at every setting. Only the camera arm leaves the platform
Clearances (measured, every setting, incl. 50 mm sway) phone and holder ≥ 403 mm from guests' heads at the deck edge; pole face above the deck ≥ 402 mm from the deck edge
Mass 173 kg fixed + 99.5 kg rotating (step box 5.8 kg separate). The empty booth's lowest overturning SF is 2.21 (a lift at the arm end); sliding SF 3.6
Footprint sweep r 1.30–1.57 m incl. sway; stanchions 0.5 m outside; fits the 4.6 × 4.6 m venue with the attendant station at every pin setting (margin ≥ 3 mm at the longest / leaning settings, by design)
Godot export P360_booth_v3_1.glb (metres, Y up), under P360_Booth:
  • Static: Platform, Frame, Base, Column, Bearing_FixedRace, Drive (the four drive units), StepBox, StepInterlock.
  • Rotating: Bearing_RotatingRace, Turntable (the plate the wheels run on), Arm, Counterweight, TiltHinge_Base and TiltHinge_Pivot › Pole, PhoneHolder.
TiltHinge_Pivot sits on the hinge axis at the 1350 reach (tilt about its local X, outward negative)

Safety (proportionate)

  • Hard-wired e-stop at the attendant station cuts motor power; no restart after power returns without a fresh Start.
  • Step box interlock (positive-opening, fail-safe wiring): no Start while the box is at the entrance.
  • Low maximum speed, 2 s soft start and stop. Wheel slip limits the drive force (29 N at the arm end); it is set with a spring at each wheel and must be measured and recorded at commissioning and at every service.
  • Separation ring (stanchions 0.5 m outside the sweep) and an attendant; the arm parks 90° from the entrance.
  • Closed skirt to 5 mm off the floor; only the camera arm passes the brush strip (25 mm finger gaps); the counterweight stays inside. Each wheel nip has its own hood.
  • Equal 100 mm risers on the step box; contrasting nosings on the rim and the box.
  • Pinned reach, height and tilt (R-clips and lanyards); the tilt gate lets the pole be pinned only at a safe reach; stop bolts keep the tube overlaps; phone tether.

Proof test before anyone stands on it (1.5 × each target group):

  • 120 kg sandbags on the four footprints of the 1 + 2 + 1 rows (480 kg);
  • then 225 kg on the larger guest's footprint at the back and 120 kg on each front footprint (465 kg);
  • then 300 kg at the platform edge between two outriggers, stepped round to every outrigger gap.

Also 300 kg on the step box front edge and a 450 N lift at the arm end on the empty booth. Record deflection under load and after unloading. Pass = no permanent set, no pad lifting, no cracking. A clean CAD model is not proof of safety.

Open items

  1. Reviewer:
    • structural review of the spider (48 mm hub sleeve engagement on the spigot, 47 MPa contact; 8 mm ring plate), base box, the 3 mm RHS walls under bolt load;
    • the arm clamp cheeks welded to the rotating plate (v3.0's model left them 6 mm short of it);
    • the drive concept: wheel slip as the torque limit instead of a sourced limiter, the pivot and spring, the nip hoods;
    • the two-part counterweight (the tier bridging the arm, its fixings; the trim rods);
    • the lighter tilt hinge and the tilt gate; misuse cases P1–P5 and I1 walk-in impact (HOLD).
  2. Owner decisions reported, not hidden:
    • 2 × 15 mm plywood instead of 2 × 18 (passes the deck checks; the proof test confirms it);
    • the counterweight is 25 mm inside the deck edge (was 45) and weighs 63.5 kg (was 52);
    • 4 standard adults, or 3 with one larger guest, all in a close pose (the footprints are assumed);
    • tilt −5° to +15° instead of ±45°;
    • only the top pole settings frame the full groups at every reach.
  3. Supplier data to confirm:
    • a polyurethane drive wheel (Ø40 × 20) and a pivot spring rated for at least 129 N; neither is sourced yet;
    • the PG19 gearbox length (93 mm assumed for motor + gearbox), the gear motor mass, and the motor's pull-out torque at about 900 rpm;
    • the interlock switch (5 mm plunger travel assumed) and the step box mat;
    • the exact universal clamp and its tilt head;
    • igus confirmation of the PRT-01 orientation and friction (μ 0.2 assumed; it decides the drive torque).
  4. Tests: wheel grip μ on the plate (dry, dusty) and the slip setting at each wheel; wheel wear; 3- and 4-person standing tests on a 1.15 m disc; S3 coast with power off; framing at each lens height; sway; tilt gate fit; interlock function; empty-booth lift at the arm end; proof test.
  5. Godot: the export is validated structurally. The separate viewer in C:\Project FreeCAD\godot still shows v3.0 until tools/export_booth_data.py is rerun.

Earlier versions are tagged: v1.6-final (branch v1.6-archive), v2.3-final (notch step), v2.4, v2.5, v2.6 (Ø0.9 m), v3.0 (250 mm, chain drive).